@Exellent I expected the knutwurst-marlin firmware to already have everything set up in that regard honestly… As fare as I know all that stuff doesn't have to do anything with the motor noise (which should be constant motor voltage - again something different than what you calibrate with the tiny hardware knob) but print quality.
@Exellent As far as I know the Trigorilla 0.0.2 doesn't support different operation modes for drivers, at least that's what I read online. So I did as I read and simply put them in, dialed in the correct voltage, switched the dir_pin in the config and that's it.
I ordered these. https://de.aliexpress.com/item/1005004582711693.html I only read later about quality issues and that there indeed are different kinds of 2209 drivers out there. So I expect this to be the cause; pretty frustrated right now, I hate my lack of exp.
@Exellent Danke, das werde ich definitiv anschauen. :)
Wird dann vermutlich alles gemacht wenn ich das Kontrollboard ohnehin in eine externe Box auslager damit die nicht in der zu bauenden heat chamber frittieren.
I've never seen such a weird failure pattern before… does the (bowden) extruder miss steps? 🧐
Anyone else ever see something like this? Could be caused by filament as well (JAYO PLA matt grey). Well, basically it could be anything at this point. Didn't have this problem with the Recyclingfabrik rPLA yesterday though… any hints and ideas welcome. #3DPrinting
@Bundesregierung Schafft zusätzlich ein Grundrecht auf wohnen wie unsere nordischen Nachbarn. Ansonsten wirds immer jene geben die komplett abgehängt wurden.
@atarifrosch@Bundesregierung Ach, gemessen an der Unterfinanzierung aller Sozialausgaben und Neolibertären Ideologie die verfolgt wird (weswegen Wohnraumspekulation nichts handfestes entgegen gesetzt wird) sind das ohnehin alles leere Worthülsen. So lange diese seit den 80ern anhaltende Katastrophe weitergeht werden die Menschen verzweifelter und wütender, die Reichen reicher, die Rechten stärker und unser aller Leben schlechter. Cum-Ex Kanzler und FDP'ler sind die letzten die da was ändern.
@momo@hellomiakoda Usually this comes from people who're just annoyed that others are different, who are too uneducated to understand that their reality (i.e. perception, feelings, ecetera) is not the same as someone else's. They therefore get annoyed at you for not fitting their expectation, but of course they say something completely different (and blame others) because they don't even properly understand what their fucking problem is.
It's kinda sad, looking at it from that perspective.
@Dexruus@frankobert@lovinurbanism Und was Robert sagt stimmt so jetzt ohnehin nicht, Stichwort aufstocken. Und das ist ausdrücklich keine Kritik am ohnehin zu niedrigen Bürgergeldsatz…
Second try. Almost good, the push pin connection of the two parts is still too weak though (melted mine together). Going to tweak it a little before uploading. :)
@kaia It's owned / made by war criminals who do illegal things all the time and just recently sold private messages of their users to others as well as backdoored user devices to spy on both them and other companies.
"You could speak a thousand tongues and still fail [to understand] if you lack knowledge of another's culture."Grimoire Weiss, Nier Replicant Ver. 1.224… ❤Green Humanist. 🍀🖖 Despises tech mega corps with a passion. Repairs shit. Helps people. Ethics > Laws.#Fedi22 #Privacy #linux #OpenSource #gaming #politics #humanism #anime #yuri #trans #tech #3DPrinting #rust #diy #Godot #RightToRepair #nobot