Conversation

Notices

1. Embed this notice
   Mr. Bacon (tony@clew.lol)'s status on Saturday, 17-Feb-2024 13:37:20 JST Mr. Bacon

   • 受不了包
   @shibao
   • 受不了包 likes this.
   • Embed this notice
     受不了包 (shibao@misskey.bubbletea.dev)'s status on Saturday, 17-Feb-2024 13:37:28 JST 受不了包

     in reply to

     @Tony@clew.lol nice but why they no use coolan

   • Embed this notice
     The Forbidden Dreamer (forbiddendreamer@poa.st)'s status on Saturday, 17-Feb-2024 14:31:54 JST The Forbidden Dreamer

     in reply to

     • 受不了包
     @shibao @Tony Carbide either needs extreme flood coolant or nothing at all. Being a ceramic, it can handle heat pretty well, but if you don't keep it entirely submerged in coolant the thermal differences will cause it to chip or shatter. In this particular case, it look like it would be difficult to keep adequate coolant on the insert, and they're using inserts, which are (relatively) cheap to replace.
     受不了包 likes this.
   • Embed this notice
     WhitestTemplar (whitesttemplar@poa.st)'s status on Sunday, 18-Feb-2024 00:18:36 JST WhitestTemplar

     in reply to

     • 受不了包
     • The Forbidden Dreamer
     @ForbiddenDreamer @shibao @Tony Suppose it also depends on the throughput they are doing, and since it is a manual system, I assume it is relatively low throughput for the day.
     受不了包 likes this.
   • Embed this notice
     IsraelDelendaEst (israeldelendaest@poa.st)'s status on Sunday, 18-Feb-2024 00:19:15 JST IsraelDelendaEst

     in reply to

     • 受不了包
     • The Forbidden Dreamer
     • WhitestTemplar
     @WhitestTemplar @ForbiddenDreamer @shibao @Tony I would assume they need a fair number per shift, but they're not running that job day in day out. Smells of batch rather than continuous production.
   • Embed this notice
     受不了包 (shibao@misskey.bubbletea.dev)'s status on Sunday, 18-Feb-2024 00:19:15 JST 受不了包

     in reply to

     • The Forbidden Dreamer
     • IsraelDelendaEst
     • WhitestTemplar

     @IsraelDelendaEst@poa.st @WhitestTemplar@poa.st @ForbiddenDreamer@poa.st @Tony@clew.lol machinist fedi groups...

   • Embed this notice
     Mr. Bacon (tony@clew.lol)'s status on Sunday, 18-Feb-2024 00:36:17 JST Mr. Bacon

     in reply to

     • 受不了包
     • The Forbidden Dreamer
     • IsraelDelendaEst
     • WhitestTemplar
     I wasn't expecting this
     
     Pleasantly surprised tbh
     受不了包 likes this.
   • Embed this notice
     Phantasm (phnt@fluffytail.org)'s status on Sunday, 18-Feb-2024 00:36:21 JST Phantasm

     in reply to

     • 受不了包
     • The Forbidden Dreamer
     • IsraelDelendaEst
     • WhitestTemplar
     @IsraelDelendaEst @Tony @shibao @ForbiddenDreamer @WhitestTemplar Those carbide inserts have a manufactured standard lifetime of 15 minutes. If you want more, you would need to lower the speed at which you are cutting the material. Maximum is usually around an hour.
     受不了包 likes this.
   • Embed this notice
     Narada (narada@foxgirl.lol)'s status on Sunday, 18-Feb-2024 00:39:05 JST Narada

     in reply to

     • 受不了包
     • The Forbidden Dreamer
     • IsraelDelendaEst
     • WhitestTemplar

     I need to get a mill, man. At this rate I will always be an apartment cuck tthough

     受不了包 likes this.
   • Embed this notice
     受不了包 (shibao@misskey.bubbletea.dev)'s status on Sunday, 18-Feb-2024 00:39:25 JST 受不了包

     in reply to

     • Narada

     @narada@foxgirl.lol i wanna use a lathe more often it's so fun -3-

   • Embed this notice
     受不了包 (shibao@misskey.bubbletea.dev)'s status on Sunday, 18-Feb-2024 00:41:34 JST 受不了包

     in reply to

     @Tony@clew.lol i've honestly been thinking about it, the only problem for me is that i'd basically have to save up the same amount of money to either put into a down payment or a trailer, they're both pretty similar, and then the loan on it would be like a car instead of a house
     so like house trailer seems totally worse but i've been considering it because just selling some land with hookups and being able to move (theoretically) is kind of appealing

   • Embed this notice
     Mr. Bacon (tony@clew.lol)'s status on Sunday, 18-Feb-2024 00:41:35 JST Mr. Bacon

     in reply to

     • 受不了包
     • The Forbidden Dreamer
     • IsraelDelendaEst
     • Narada
     • WhitestTemplar
     Don't get offended, but what about a manufactured home or a trailer? Hell of a lot cheaper and you can get a plot of land.
     
     I've been thinking about it because anything half way decent around here is 500K